Starrett Height Transfer Gages 252 Series
The Starrett No. 252 Height Transfer Gage is and ideal instrument for use with test indicators or electronic amplifiers to accurately transfer height settings from gage blocks, height gages and other standards.
Accuracy and Long-Life Features
• Extreme rigidity provides the vibration-proof stability necessary to permit precise, repeat readings with indicators of the highest amplification
• Extremely rigid, rectangular box-type hollow column mounted integrally on a heavy base
• Because the adjusting mechanism is located in the base, the vertical column and indicator are isolated and not affected by an external influence such as heat or hand pressure
Ease-of-Operation Features
• Hand-fitting base design for sure-grip handling and easy movement
• Bottom of the base has three-point stability and smooth movement on the surface plate
• An adjustable slide, incorporating a snug for holding test indicators or electronic gage heads, has rapid vertical manual adjustment
• The slide can be locked at the desired height by a thumb screw
• The entire slide unit has fine vertical adjustment of approximately 3/8" (9.5 mm) relative to the fixed column by means of a knob on the base. This permits the slide with its test indicator to by quickly and precisely adjusted to the desired setting
Tool and Gaging Holders
• A snug on the slide provides two holes .375" (9.5 mm) and .156" (4 mm) diameter for holding gage rods or scribers. A 9" (225 mm) rod furnished with the gage is especially useful for reaching confined areas or reaching heights greater than the range of the gage
• The rod has a major diameter of .375" (9.5 mm) and two stepped diameters of 1/4" (3.2 mm) and 7/32" (5.5 mm) at one end and 5/16" (8 mm) at the opposite end. Starrett No. 708 and 709 Test Indicators can be mounted on this rod using Starrett No. PT22428 clamp. Starrett No. 196 Test Indicators can be mounted using Starrett snugs, Part Nos. PT99439 or PT99440 (snugs not furnished)
• Also furnished with the gage is the No. 657J Gage-Holding Rod to accommodate the Starrett No. 715-1 Gaging Head when the Transfer Gage is used with the No. 715 Electronic Gage. A convenient wire retaining clip mounted on the movable slide keeps electronic gage head cables from deflecting the gage-holding rod
• Starrett No. 25, No. 81, No. 655 and be used on the height gage by means of a No. 657J Gage Rod (furnished). Other useful attachments (extra) are Starrett surface gage spindles [No. 57C or No. 57D, 12" (300 mm) and 18" (450 mm)] - which are extremely useful for scribing and layout

Electronic Digital Height Gage No. 755
The No. 755 Electronic Height Gage provides measuring information directly to Starrett SPC Plus® Data Collection Systems for analysis, data collection and hard copy documentation.
Readability and Control Features
• Easy-to-read LCD display with .0001" (0.001 mm) resolution, instant inch/millimeter conversion and ± .0002" (±0.005 mm) linear accuracy
• Hold feature allows a reading to be taken in difficult positions, and then the gage may be moved without losing the reading
• Zero function permits the gage to float "zero" anywhere within the range of the gage
• Plus or minus indication allows reading in proper direction
• Special base design allows direct reading from zero over full range
Ease-of-Handling Features
• Quick adjustment is accomplished by means of a split nut providing rapid traverse
• Ultra-fine adjustments are achieved by a knob located on the base, thereby isolating the column and slide from external pressures
• Hardened, ground, and lapped vibration-proof base has finger grooves that provide for ease of movement
• Starrett balanced design - the vertical column is positioned near the center of the base for stability, not at the edge as on competitive tools
• A variety of attachments are available for the No. 755 Height Gage, allowing the mounting of electronic indicator gaging heads, dial indicators, and scribers
Battery Life
• The gage is portable, with an optional rechargeable battery pack that provides up to eight hours of intermittent operation

$601.80

Master Vernier Height Gages No. 254, 254M, 254EM Series
This Master Vernier Height Gage is the ultimate height gage design and is the experienced craftsman's friend. It is a rugged and reliable tool that gives precise and dependable measurements over long ranges. This tool is accurate, has the easiest reading vernier style, is stronger, and is offered in greater ranges than other height gages.
Readability Features
• Long, 50-division vernier scales made popular by Starrett. This feature permits just half as many bar graduations as conventional single vernier tools. These widely spaced graduations make possible easy reading to .001" or 0.02 mm without needing a magnifying glass.
• Flush fitting of the vernier scales to the main scale means that these are in the same plane, which eliminates parallax. Vernier scales are adjustable
• Black lines and figures against Starrett satin chrome finish make reading a pleasure, not an effort
• The scriber and base are designed for direct reading from zero (bottom of base)
Ease-of-Handling Features
• Quick-adjust release on the slide allows for fast positioning
• Extremely fine adjustments are achieved by a knob located on the base, thereby isolating the column and slide from external pressures
• Additional remote fine adjustment located on top of the bar for sizes 36" (900 mm) and larger - convenient feature when working in higher ranges
• Special master bar design and the balanced design and weight of the base eliminates vibration - especially helpful with fully extended scribers
• Master bars on models up to 24" and 600 mm are hardened and stabilized
• Base is hardened, ground, and lapped square with the bar and has finger grooves to provide ease of movement
• The vertical bar is positioned near the center of the base for balance and stability
• Versatile tool will scribe lines, mount dial indicators or electronic probes, and accept depth attachments
• Tool can also be used with our No. 359 Protractor for checking angles
• The auxiliary scriber has a rounded nose for cutting clean, sharp lines with smoothness and less pressure - a Starrett original feature

Vernier Height Gages No. 255, 255M, 255EM Series
This is the "baby brother" of the No. 254 Master Vernier Height Gage. It is essentially the same tool, but a much lighter version for normal use where heavy duty applications are not practical. The 18" and 450 mm models weigh 3 1/4 lbs. (1.5 kg.). No other height gage features this favorable combination of design, weight, and accuracy.
Readability Features
• Long,, 50-division vernier scales that can be read to .001" or 0.02 mm without a magnifying glass
• Flush-fitting of the vernier scales to the main scale eliminates parallax
• Easy-reading sharp black lines and figures against Starrett satin chrome finish background
• The scriber and the base are designed so that the gage will read directly from zero
Ease-of-Handling Features
• Slides easily for quick adjustment and has a screw type adjusting nut on the bar for precise positioning
• The design of the hardened and stabilized bar plus the balanced design and weight of the base eliminate vibration
• The base is hardened, ground, and lapped and is hand shaped for sure grip and easy movement
• The vertical bar is positioned near the center of the base for balance and stability
• Ability to scribe lines, measure with dial indicators or electronic probes and accept depth attachments
• The auxiliary scriber has a rounded nose for cutting clean, sharp lines with smoothness and less pressure. This is an original Starrett feature.

Electronic Digital Height Gage (with output) No. 751
This height gage is light, portable and easy to use for vertical measurements within its range. Also, all measurement information can be entered directly into Starrett Data Collection Systems for analysis, data collection, and hard copy documentation.
Readability Features
• Clear, easily read numbers, properly sized for the tool
Design Features for Accuracy and Long Life
• Exclusive Starrett-designed microprocessor chip
• Hardened, stainless steel bar for long life
• Depth attachment No. PT 08680A available for measuring depth of holes, slots, and recesses
• Fine adjustment thumb roll for precision measurements
• The auxiliary scriber has a rounded nose for cutting clean, sharp lines with smoothness and less pressure. This is an original Starrett feature
• Lock to hold the slide in position
• Hardened, ground, and lapped base with finger grooves to provide ease of movement
• One-year minimum battery life with two 3-volt batteries, No. CR2032
• Linear Accuracy: ± .001" (± 0.03 mm); Resolution: .0005" (0.01 mm)
• Vertical bar is back from the edge of the nose for better stability
• Nose is designed to let the scriber reference zero from the bottom of the base to get the full 6" (150 mm) usable range
Action Features with Five Control Buttons and the New Easy-to-Use Shift Button
• Inch-millimeter conversion
• Zero at any position
• Hold readout at any position
• Manual ON/OFF plus a built in automatic OFF after 15 minutes of nonuse
• Exclusive shift button allows for easy use of more functions
• LIMITS - after using the shift button, pressing LIMITS enters high and low dimensional limits. Out of limits readings will now show a flashing display