Starrett-Webber Square Combination croblox® and Steel
Metric System - Gage Block Sets in Case

An ideal combination of value, price, and convenience, these sets include a popular selection of croblox® and steel as listed.
With NVLAP Accredited Commercial Grade Calibration and Etched Serial Numbers
Two Millimeter Base
U.S. Fed. Accuracy Grade 2*
Part Number Blocks Per Set Page Price  
S2C45.MA1 45 Blocks 558 $2,263.20

Measuring Range:
6.0 Through 450 in .001 mm Steps
4.0 Through 450 in .01 mm Steps
2.0 Through 450 in .1 mm Steps

Blocks Included in Sets:
9 Blocks 2.001 Through 2.009 (Steps of .001 mm)
9 Blocks 2.01 Through 2.09 (Steps of .01 mm)
9 Blocks 2.1 Through 2.9 (Steps of .1 mm)
9 Blocks 1.0 Through 9.0 (Steps of 1.0 mm)
9 Blocks 10 Through 90 (Steps of 10 mm)
S2C45.MA1X 45 Blocks 558 $2,564.04

Measuring Range:
6.0 Through 450 in .001 mm Steps
4.0 Through 450 in .01 mm Steps
2.0 Through 450 in .1 mm Steps

Blocks Included in Sets:
Same as Above Plus the Following Accessories:
1 pair SA102 6 mm Radius Jaws
1 each SA4 Scriber Point
2 each SA7 Knurled Screws
2 each SA8 Studs
2 each SA9 Flat Head Screws (long)
2 each SA10 Flat Head Screws (short)
2 each SA11 Slotted Nuts
1 each SA12 19 mm Tie Rod
1 each SA13 38 mm Tie Rod
1 each SA14 57 mm Tie Rod
1 each SA15 76 mm Tie Rod
1 each SA16 114 mm Tie Rod
S2C88.MA1 88 Blocks 558 $4,438.64
Measuring Range:
6.0 Through 450 in .0005 mm Steps
4.0 Through 450 in .001 mm Steps
2.0 Through 450 in .01 mm Steps
2.0 Through 450 in .1 mm Steps
Blocks Included in Sets:
1-.5 mm
1-2.0005 mm
9-2.001 Through 2.009 (Steps of .001 mm)
49-2.01 Through 2.49 (Steps of .01 mm)
18-1.0 Through 9.5 (Steps of .5 mm)
10-10 Through 100 (Steps of 10 mm)
S2C112.MA1 112 Blocks 558 $4,949.05

Measuring Range:
6.0 Through 250 in .0005 mm Steps
4.0 Through 250 in .001 mm Steps
2.0 Through 250 in .01 mm Steps
2.0 Through 250 in .1 mm Steps
Blocks Included in Sets:
1-.5 mm
1-2.0005 mm
9-2.001 Through 2.009 (Steps of .001 mm)
49-2.01 Through 2.49 (Steps of .01 mm)
48-1.0 Through 24.5 (Steps of .5 mm)
4-25 Through 100 (Steps of 25 mm)

** NOTE: All blocks are croblox®, except sizes below 1.5 mm and above 10 mm, which are steel.

NOTE: Metric croblox® Wear Blocks are available as option. To order, contact [email protected].

Sets also available without calibration or etched serial numbers, or with NVLAP Accredited Master Grade Calibration and Etched Serial Numbers, contact [email protected].

For complete accuracy specifications, see Standards of Accuracy.

Top

Ecommerce system powered by the DXCART Solution. DXCART © Copyright 1996-2001 DXStorm Inc.
All Rights Reserved. DXCART is a trademark of DXStorm Inc.